Skip to main content
(828) 649-7190
Same Day Shipping Before 2pm EST

Farmall Cub Carburetor: IH Cub & Lo-Boy Rebuild

Is your Farmall Cub running rough? This guide covers everything you need to know about Farmall Cub carburetor maintenance and rebuilding, from identifying problems to sourcing the right parts and completing the rebuild. Get your Cub running smoothly again!

Introduction to the Farmall Cub Carburetor

The Farmall Cub, including the Lo-Boy variant, is a versatile and beloved tractor known for its compact size and reliability. A crucial component of its performance is the carburetor, responsible for mixing air and fuel in the correct ratio for efficient combustion. A properly functioning Farmall Cub carburetor ensures smooth operation, optimal fuel economy, and consistent power delivery. At Madison Tractor Company, we understand the importance of keeping your Cub running strong. This guide will walk you through troubleshooting, repair, and rebuilding your Farmall Cub carburetor. We carry a wide selection of parts for your International Harvester tractor, including carburetors, fuel pumps, filters, and more.

Recommended Parts for This Guide

3 parts we recommend — in stock, ships fast, one-click add to cart.

🔍 Looking for a specific part? Try our AI Part Finder — tell it your equipment and what you need, and it will find matching parts instantly.

Common Farmall Cub Carburetor Problems

Identifying the symptoms is the first step in diagnosing carburetor issues. Here are some common problems you might encounter:

  • Rough Idling: This could indicate a lean or rich fuel mixture, vacuum leaks, or clogged jets within the carburetor.
  • Hard Starting: Difficult starting, especially when cold, can be caused by a malfunctioning choke or an improperly adjusted fuel mixture.
  • Poor Fuel Economy: A carburetor that's running too rich (too much fuel) will significantly reduce fuel efficiency.
  • Hesitation or Stalling: These issues can stem from a lean fuel mixture, a dirty carburetor, or a malfunctioning accelerator pump.
  • Black Smoke: Indicates an excessively rich fuel mixture, often due to a stuck float or a faulty needle valve.
  • White Smoke: White smoke is usually related to coolant burning in the cylinder from a cracked head, or bad head gasket and is not directly related to the carburetor, but if your engine has been running improperly due to a faulty carburetor, it may have caused the other symptoms.

Before diving into a rebuild, always check the basics: ensure you have clean fuel, a properly functioning fuel pump (consider upgrading to an electric tractor fuel pump if you're experiencing frequent issues), and no air leaks in the intake manifold.

Tools and Materials for Carburetor Rebuild

Before starting your Farmall Cub carburetor rebuild, gather the necessary tools and materials:

  • Carburetor Rebuild Kit: Contains gaskets, seals, needle valve, and other essential components. Make sure to get one specific to your carburetor model. We also offer Viton Zenith kits and IH-specific kits.
  • Carburetor Cleaner: Use a high-quality carburetor cleaner to dissolve varnish and deposits.
  • Small Screwdrivers: Both flathead and Phillips head screwdrivers in various sizes.
  • Pliers: Needle-nose pliers are particularly useful for removing small parts.
  • Wrenches: A set of open-end wrenches and sockets.
  • Soft Wire Brush: For cleaning carburetor components without damaging them.
  • Compressed Air: To blow out passages and dry parts.
  • Clean Work Area: A well-lit and organized workspace is essential.
  • Camera or Phone: Take pictures as you disassemble the carburetor to help with reassembly.
  • Parts Tray: To keep small parts organized.

Farmall Cub Carburetor Rebuild Process: Step-by-Step

Safety First: Disconnect the battery before working on the fuel system to prevent accidental sparks. Work in a well-ventilated area.

  1. Removal: Carefully disconnect the fuel line, throttle linkage, and any other connections to the carburetor. Remove the carburetor from the intake manifold.
  2. Disassembly: Using your camera, document each step of the disassembly process. Remove the float bowl, float, needle valve, jets, and any other removable components.
  3. Cleaning: Thoroughly clean all carburetor parts with carburetor cleaner and a soft wire brush. Pay close attention to the jets and passages, ensuring they are clear of any obstructions. Use compressed air to blow out all passages.
  4. Inspection: Inspect all parts for wear or damage. Replace any worn or damaged components with new parts from your rebuild kit. Check the float for leaks by submerging it in hot water; bubbles indicate a leak.
  5. Reassembly: Carefully reassemble the carburetor, following the pictures you took during disassembly. Install new gaskets and seals from the rebuild kit. Pay attention to the orientation of each part.
  6. Adjustment: Once the carburetor is reassembled, adjust the float level according to the manufacturer's specifications. This is crucial for proper fuel metering. Typically the float level will be around 5/16" when inverted.
  7. Installation: Reinstall the carburetor onto the intake manifold, ensuring a tight seal. Reconnect the fuel line, throttle linkage, and any other connections.
  8. Testing: Start the engine and allow it to warm up. Adjust the idle mixture screw and idle speed screw to achieve a smooth idle. Fine-tune the adjustments as needed.

Specific Steps for Common Carburetors on the Farmall Cub

The Farmall Cub typically used carburetors manufactured by Zenith or Marvel-Schebler. While the general principles of rebuilding are the same, some specific details may vary.

Zenith Carburetors:

  • Main Jet: Ensure the main jet is clean and properly sized. A partially clogged main jet can cause lean running at higher engine speeds.
  • Idle Mixture Screw: Adjust the idle mixture screw until the engine idles smoothly. Turning the screw in will lean the mixture, while turning it out will richen the mixture.

Marvel-Schebler Carburetors:

  • Choke Adjustment: Marvel-Schebler carburetors often have a more complex choke mechanism. Ensure the choke plate closes fully when the choke is engaged and opens fully when disengaged.
  • Float Level: Proper float level is critical for Marvel-Schebler carburetors. Refer to the service manual for the correct float level specification.

Troubleshooting After Rebuild

Even with a careful rebuild, problems can still arise. Here are some common post-rebuild issues and how to address them:

  • Engine Won't Start: Check for fuel flow to the carburetor. If no fuel is present, check the fuel pump and fuel lines. If fuel is present, check the ignition system.
  • Rough Idle: Adjust the idle mixture screw. If the idle remains rough, check for vacuum leaks around the intake manifold or carburetor base.
  • Hesitation: This can be caused by a lean fuel mixture or a malfunctioning accelerator pump. Check the accelerator pump nozzle to ensure it is delivering fuel when the throttle is opened.
  • Flooding: Flooding (excessive fuel) can be caused by a stuck float or a leaking needle valve. Check the float and needle valve for proper operation.

Preventative Maintenance for Your Farmall Cub Carburetor

Regular maintenance can prevent many carburetor problems. Here are some tips:

  • Use Clean Fuel: Always use clean, fresh fuel. Consider adding a fuel stabilizer if the tractor will be stored for an extended period.
  • Fuel Filter: Replace the fuel filter regularly to prevent dirt and debris from entering the carburetor.
  • Inspect Fuel Lines: Inspect fuel lines for cracks or leaks. Replace any damaged fuel lines.
  • Check Air Filter: Make sure your air filter is clean and functioning correctly. A dirty air filter restricts airflow and can cause the carburetor to run rich.

Beyond the Carburetor: Other Fuel System Components

While the carburetor is critical, remember that it's just one part of the fuel system. Ensure other components are in good working order for optimal performance. This includes checking your fuel pump, fuel lines, and fuel filter regularly. Madison Tractor Company carries a full range of parts for tractors of all major brands including John Deere, Case IH, Ford, New Holland, Massey Ferguson, Kubota, Allis Chalmers, Deutz, International Harvester, Oliver, White, Gleaner, Vermeer, Hesston, Mahindra, and Zetor. We stock radiators, water pumps, starters, alternators, hydraulic pumps, cylinders, clutch kits, PTO parts, fuel pumps, carburetors, injectors, filters, gaskets, pistons, bearings, seals, belts, chains, concaves, and sickle sections.

Remember to also check related articles in our "Tractor Fuel System, Carburetor & Injection Parts" cluster, such as our guides to John Deere tractor carburetors, Ford tractor carburetors, Massey Ferguson carburetors, and Farmall carburetors. We also have guides to tractor diesel injectors and tractor fuel pumps for various makes and models.

Find Your Farmall Cub Carburetor Parts at Madison Tractor Company

Madison Tractor Company is your trusted source for high-quality Farmall Cub carburetor rebuild kits and replacement parts. We offer options like the Zenith "Viton" kit and IH-style kit to keep your IH Cub and Lo-Boy running smoothly for years to come. Browse our online catalog or contact our knowledgeable parts specialists for assistance in finding the right parts for your tractor. Don't let a faulty carburetor sideline your Farmall Cub – get the parts you need today!

Shop with Confidence at Madison Tractor Company!

We know you rely on your vintage iron. If you are searching for parts for your tractor, combine, or hay equipment, visit our site for a wide selection of parts for all major brands, including John Deere, Case IH, Ford, New Holland, Massey Ferguson, Kubota, Allis Chalmers, Deutz, International Harvester, Oliver, White, Gleaner, Vermeer, Hesston, Mahindra, and Zetor.

🔍 Can't Find Your Part?

Use our AI-Powered Part Finder to search by your equipment's make, model, and what you need. It's the fastest way to find the exact part for your machine.

Try the Part Finder →