Briggs & Stratton Head Gasket: By Engine Model
A leaking head gasket can cause serious problems with your Briggs & Stratton engine. Learn how to identify the correct replacement for your specific engine model and get your equipment running smoothly again.
The head gasket on your Briggs & Stratton engine is a critical component. It seals the combustion chamber between the cylinder head and the engine block, preventing compression loss and coolant or oil leaks. When a head gasket fails, it can lead to reduced engine performance, overheating, and even engine damage. Choosing the correct briggs head gasket for your specific engine model is essential for a successful repair.
Recommended Parts for This Guide
1 part we recommend — in stock, ships fast, one-click add to cart.
🔍 Looking for a specific part? Try our AI Part Finder — tell it your equipment and what you need, and it will find matching parts instantly.
Understanding Head Gasket Function and Failure
The head gasket's primary job is to maintain a tight seal under extreme pressure and temperature. It's a consumable part, meaning it will eventually wear out or fail. Common causes of failure include:
- Overheating: Excessive heat can warp the cylinder head or block, compromising the gasket's seal.
- Detonation: Abnormal combustion can create intense pressure spikes that damage the gasket.
- Corrosion: Coolant leaks can corrode the gasket material over time.
- Improper Installation: Incorrect torque or a damaged gasket during installation can lead to premature failure.
Identifying the Correct Briggs Head Gasket
The most important step in replacing a briggs head gasket is identifying the correct part number for your specific engine. Briggs & Stratton engines are identified by three sets of numbers: the Model, Type, and Code. These numbers are typically stamped on the engine itself, often near the spark plug or on the valve cover. Write these numbers down before ordering any parts.
Once you have the Model, Type, and Code numbers, you can use a parts lookup tool on the Madison Tractor Company website to find the correct head gasket. Most Briggs Head Gaskets are specific to certain engine models, so using this tool helps ensure you get the right one.
For example, if you are looking for a briggs carburetor rebuild kit or a replacement briggs and stratton carburetor you will need the same Model, Type and Code to find the correct parts.
Common Briggs & Stratton Engine Series and Head Gaskets
While using the model lookup tool is best, here are some common Briggs & Stratton engine series and general information about their head gaskets:
Intek Series
The Intek series is a popular choice for many lawn tractors and riding mowers, including those from brands like Craftsman, Cub Cadet, and John Deere. Intek engines often use multi-layered steel (MLS) head gaskets for improved sealing and durability. Some common part numbers to look for in our database include 795361, 692136, and 794147. Be sure to always verify fitment by using the engine model number.
Quantum Series
Quantum engines are commonly found on push mowers. These engines typically use a composite head gasket. These gaskets may be suitable for models from Toro and Murray. Some gaskets can be found for around $10-$15.
Professional Series
The Professional Series engines are designed for heavier-duty applications, and often found on Husqvarna and some John Deere models. They typically use a more robust head gasket material. They also may use multiple gaskets. Always reference the parts diagram for your engine.
Replacing Your Briggs Head Gasket: Step-by-Step
Safety First! Always disconnect the spark plug wire before working on your engine. Allow the engine to cool completely before starting. Wear safety glasses and gloves.
- Remove the Engine Shroud and Accessories: Take off any shrouds, covers, or accessories that block access to the cylinder head. This may include removing the muffler or carburetor. Be careful when removing the briggs and stratton carburetor to avoid damaging any fuel lines or linkages.
- Remove the Cylinder Head: Carefully loosen and remove the cylinder head bolts. Refer to your engine's service manual for the correct torque sequence and specifications. Cylinder heads can be heavy.
- Inspect the Cylinder Head and Block: Clean any debris or old gasket material from the cylinder head and engine block surfaces. Check for any signs of warping or damage. A warped head needs to be resurfaced by a machine shop.
- Install the new head gasket: Carefully position the new briggs head gasket onto the engine block. Ensure it's aligned correctly with the bolt holes and any coolant or oil passages. Some gaskets may have a specific orientation; refer to the gasket packaging or service manual.
- Reinstall the Cylinder Head: Place the cylinder head back onto the engine block, aligning it with the gasket and bolt holes.
- Torque the Cylinder Head Bolts: Tighten the cylinder head bolts to the specified torque in the correct sequence. Refer to your engine's service manual for the exact torque values and sequence. This is a crucial step to ensure a proper seal.
- Reassemble the Engine: Reinstall all the components you removed earlier, such as the muffler, carburetor, and engine shroud. Reconnect the spark plug wire.
- Test the Engine: Start the engine and check for any leaks or unusual noises. Monitor the engine temperature to ensure it's not overheating.
If your engine also requires fuel system work, consider purchasing a small engine fuel pump or a kohler fuel pump if you have a Kohler engine. Remember to consult the appropriate parts diagrams for your engine type.
Tips for a Successful Head Gasket Replacement
- Use a Torque Wrench: Using a torque wrench is essential for properly tightening the cylinder head bolts. Overtightening can damage the bolts or the cylinder head, while undertightening can lead to leaks.
- Cleanliness is Key: Ensure all surfaces are clean and free of debris before installing the new gasket.
- Refer to the Service Manual: Always consult your engine's service manual for specific instructions and torque specifications.
- Inspect Other Components: While you have the engine apart, inspect other components, such as the valves, piston, and cylinder walls, for any signs of wear or damage. Now is a good time to also replace the spark plugs.
- Consider a Professional: If you're not comfortable working on your engine, consider taking it to a qualified mechanic.
Brands We Support
Madison Tractor Company stocks briggs head gasket replacements and other parts for a wide variety of outdoor power equipment brands including John Deere, Craftsman, Cub Cadet, Husqvarna, Toro, Ariens, Murray, Hustler, Scag, Exmark, Ferris, Snapper, Simplicity, and Dixie Chopper.
In addition to engine parts, we also carry a wide selection of other replacement parts for your equipment such as belts, blades, spindles, pulleys, filters, bearings and shear pins.
Why Choose Madison Tractor Company?
Replacing a briggs head gasket is a crucial maintenance task. Choosing the right part ensures long-lasting performance. Whether you are working on a lawn mower, snow blower, or other piece of equipment, we have the parts you need.
Need a riding mower fuel pump? What about a small engine carburetor kit for that old snow blower? You can find all of these and more.
Don't let a faulty head gasket sideline your equipment. Browse our selection of briggs head gasket replacements and other engine parts today. Madison Tractor Company is your trusted source for quality parts and expert advice. Shop Briggs & Stratton Engine Parts now!
🔍 Can't Find Your Part?
Use our AI-Powered Part Finder to search by your equipment's make, model, and what you need. It's the fastest way to find the exact part for your machine.
Try the Part Finder →Part of our comprehensive guide
Small Engine Parts Guide: Carburetors, Fuel Pumps & Gaskets by Engine








