Skip to main content
(828) 649-7190
Same Day Shipping Before 2pm EST

Kohler Ignition Coil: Courage & Command Engines

Is your Kohler Courage or Command engine sputtering, misfiring, or failing to start? A faulty ignition coil is a common culprit. Learn how to diagnose and replace it with this guide from Madison Tractor Company.

Introduction to Kohler Ignition Coils for Courage & Command Engines

The ignition coil is a critical component of your Kohler engine's ignition system. It transforms the low voltage from the battery into the high voltage needed to create a spark at the spark plug, which ignites the air-fuel mixture in the cylinder. When the ignition coil fails, your engine will experience starting problems, misfires, or complete failure to run. This article focuses on Kohler Courage and Command series engines, commonly found on lawn tractors, zero-turn mowers, and other outdoor power equipment.

Recommended Parts for This Guide

1 part we recommend — in stock, ships fast, one-click add to cart.

🔍 Looking for a specific part? Try our AI Part Finder — tell it your equipment and what you need, and it will find matching parts instantly.

At Madison Tractor Company, we understand the importance of having a reliable ignition system. Whether you own a John Deere, Craftsman, Cub Cadet, Husqvarna, Toro, Ariens, Murray, Hustler, Scag, Exmark, Ferris, Snapper, Simplicity, or Dixie Chopper riding mower with a Kohler engine, we can help you find the right Kohler ignition coil and other essential parts like spark plugs to keep your machine running smoothly. If you have a riding mower battery that you know is good, but the engine still won't start, the problem may lie elsewhere in the electrical system. Check out our article on riding mower starters as well.

Common Symptoms of a Failing Kohler ignition coil

Recognizing the symptoms of a failing ignition coil can save you time and prevent further damage to your engine. Here are some common signs:

  • Engine misfires: The engine runs erratically and may sputter, especially under load.
  • Hard starting or no starting: The engine cranks but fails to start consistently, or doesn't start at all.
  • Reduced engine power: The engine lacks its usual power and struggles to perform tasks.
  • Poor fuel economy: The engine consumes more fuel than usual due to incomplete combustion.
  • Engine stalling: The engine starts and runs briefly, then stalls unexpectedly.
  • Check engine light: (If equipped) Some engines have a check engine light that may illuminate due to ignition coil issues.

These symptoms can also be caused by other problems, such as a faulty spark plug, dirty air filter, or a fuel delivery issue. However, if you experience these symptoms, especially in conjunction with each other, it's worth testing your ignition coil.

Testing Your Kohler Ignition Coil

Before replacing the ignition coil, it's important to test it to confirm that it's actually the source of the problem. Here are two common methods for testing:

1. Spark Tester Method

A spark tester is a simple tool that allows you to visually check for spark at the spark plug wire.

  1. Disconnect the spark plug wire from the spark plug.
  2. Connect the spark tester between the spark plug wire and the spark plug.
  3. Crank the engine.
  4. Observe the spark tester. A strong, consistent spark indicates a functioning ignition coil. A weak, intermittent, or non-existent spark suggests a faulty coil.

2. Multimeter Method (Resistance Test)

A multimeter can be used to measure the resistance of the ignition coil windings. This test requires a basic understanding of electrical circuits and multimeter operation.

  1. Disconnect the ignition coil from the engine wiring harness.
  2. Set your multimeter to the resistance (Ohms) setting.
  3. Measure the primary resistance by placing the multimeter probes on the primary terminals of the coil. Refer to your engine's service manual for the expected resistance range.
  4. Measure the secondary resistance by placing one probe on a primary terminal and the other probe on the spark plug wire terminal. Again, refer to your service manual for the expected range.
  5. If the resistance readings are outside the specified range, the ignition coil is likely faulty.

A faulty riding mower solenoid can mimic the same issues as a bad ignition coil, so that's also a good thing to check.

Safety First: Disconnecting Power

WARNING: Before working on any electrical components, always disconnect the spark plug wire from the spark plug and remove the key from the ignition. For added safety, disconnect the negative (-) battery cable. This prevents accidental starting and electrical shock. Wear appropriate safety glasses and gloves.

Tools and Materials Needed

Gather the following tools and materials before starting the replacement process:

  • New Kohler ignition coil (ensure it's the correct part number for your engine model)
  • Socket set or wrenches
  • Screwdriver (Phillips and flathead)
  • Spark plug gapping tool or feeler gauge
  • Multimeter (optional, for testing)
  • Spark tester (optional, for testing)
  • Clean rags
  • Work gloves
  • Safety glasses

Kohler Ignition Coil Replacement Steps

Follow these steps to replace the ignition coil on your Kohler Courage or Command engine:

  1. Access the Ignition Coil: Locate the ignition coil on your engine. It's typically mounted near the flywheel. Remove any shrouds or covers that are blocking access to the coil. This might involve removing the engine's cooling shroud, which often requires a socket wrench. Pay attention to how the shrouds are installed so you can reassemble them correctly.
  2. Disconnect the Wiring: Disconnect the wires connected to the ignition coil. Note the position of each wire for correct reassembly.
  3. Remove the Old Coil: Remove the mounting bolts or screws securing the ignition coil to the engine. Carefully remove the old coil.
  4. Install the New Coil: Install the new ignition coil in the same location as the old one. Secure it with the mounting bolts or screws.
  5. Reconnect the Wiring: Reconnect the wires to the ignition coil, ensuring they are connected to the correct terminals.
  6. Set the Air Gap (Critical): Setting the correct air gap between the ignition coil and the flywheel is crucial for proper operation. See the next section for detailed instructions.
  7. Reinstall Shrouds and Covers: Reinstall any shrouds or covers that were removed to access the ignition coil.

Setting the Air Gap

The air gap is the distance between the ignition coil and the flywheel magnets. The correct air gap is essential for proper spark generation. Refer to your engine's service manual for the specific air gap specification for your Kohler Courage or Command engine. A typical air gap is between 0.010 and 0.014 inches.

Here's how to set the air gap:

  1. Loosen the ignition coil mounting bolts slightly.
  2. Insert a feeler gauge of the specified thickness between the ignition coil and the flywheel magnets.
  3. Push the ignition coil against the feeler gauge and tighten the mounting bolts.
  4. Remove the feeler gauge. The ignition coil should now be properly positioned with the correct air gap. Some people use a business card or playing card as an alternative, but a feeler gauge is more precise.

After Replacement: Testing the Engine

After replacing the ignition coil, test the engine to ensure it's running correctly:

  1. Reconnect the spark plug wire to the spark plug.
  2. Reconnect the negative (-) battery cable (if disconnected).
  3. Start the engine.
  4. Listen for smooth engine operation. Check for misfires, stalling, or other issues.
  5. If the engine still experiences problems, recheck your work and consider other potential causes, such as a faulty lawn mower ignition switch.

Preventive Maintenance for Your Ignition System

To prolong the life of your ignition coil and prevent future problems, consider these preventive maintenance tips:

  • Regularly inspect spark plugs: Replace worn or fouled spark plugs with the correct type for your engine.
  • Keep the engine clean: Remove debris and dirt from around the engine to prevent overheating.
  • Check wiring connections: Ensure all wiring connections are clean and secure.
  • Store equipment properly: Store your lawn mower or equipment in a dry place to prevent corrosion.

While replacing the ignition coil, consider inspecting and replacing these related parts as well:

  • Spark Plugs: Worn spark plugs can put extra strain on the ignition coil.
  • Air Filter: A dirty air filter can cause the engine to run lean, leading to misfires and other problems.
  • Fuel Filter: A clogged fuel filter can restrict fuel flow and cause engine stalling.
  • Flywheel Key: A damaged flywheel key can affect the engine's timing and cause starting problems.
  • Voltage Regulator: Overcharging can damage the ignition coil, so ensure that the voltage regulator is working properly.

Beyond ignition system components, remember to maintain other essential parts like blades, belts, and spindles for optimal mower performance.

By understanding the symptoms of a failing ignition coil and following these troubleshooting and replacement steps, you can keep your Kohler Courage or Command engine running smoothly. Remember to consult your engine's service manual for specific instructions and safety precautions.

Shop Kohler Engine Parts at Madison Tractor Company

Madison Tractor Company is your trusted source for Kohler engine parts and accessories. We offer a wide selection of ignition coils, spark plugs, filters, and other essential parts to keep your outdoor power equipment running at its best. Shop with confidence knowing that you're getting high-quality parts at competitive prices. Visit our website or contact us today to find the right parts for your needs!

🔍 Can't Find Your Part?

Use our AI-Powered Part Finder to search by your equipment's make, model, and what you need. It's the fastest way to find the exact part for your machine.

Try the Part Finder →