Skip to main content
(828) 649-7190
Same Day Shipping Before 2pm EST

Combine Straw Walker: Bearing & Crank Replacement

Straw walkers are a critical part of your combine's separation system. This guide walks you through replacing worn bearings and cranks to keep your combine running smoothly and efficiently. Get back in the field faster with this comprehensive repair guide.

Introduction to Combine Straw Walker Maintenance

The straw walker, or straw rack, is a vital component in your combine harvester. Its primary function is to separate any remaining grain from the straw after the threshing process. A properly functioning straw walker ensures minimal grain loss, maximizing your harvest yield. Over time, the bearings and cranks within the straw walker mechanism can wear down due to constant vibration and heavy loads. Recognizing the signs of wear and performing timely replacements is crucial for maintaining optimal combine performance. This guide will walk you through the process of replacing straw walker bearings and cranks, helping you get back to harvesting quickly and efficiently.

Recommended Parts for This Guide

4 parts we recommend — in stock, ships fast, one-click add to cart.

🔍 Looking for a specific part? Try our AI Part Finder — tell it your equipment and what you need, and it will find matching parts instantly.

This guide is applicable to many common combine models, including John Deere, Case IH, New Holland, GleanerMassey Ferguson machines. Specific OEM part numbers and torque specifications may vary depending on the model, so always consult your service manual.

Identifying Straw Walker Problems

Several symptoms can indicate issues with your combine's straw walker bearings and cranks. These

  • Excessive noise Unusual grinding, squealing, or knocking sounds coming from the straw walker area.
  • Increased vibration Noticeably more vibration than usual during operation.
  • Grain loss Higher than normal grain loss over the back of the combine.
  • Visible wear and tear Obvious signs of damage, such as cracks, play in the bearings, or bent cranks.
  • Seized or stiff movement Difficulty in the straw walker's range of motion.

If you notice any of these symptoms, it's essential to inspect the straw walker mechanism promptly to prevent further damage and costly repairs. Ignoring these problems can lead to catastrophic failure, potentially damaging other combine components.

Safety Precautions

WARNING Before performing any maintenance or repairs on your combine, always disconnect the battery and ensure the machine is properly supported to prevent accidental movement or injury. Wear appropriate personal protective equipment (PPE), including safety glasses, gloves hearing protection.

  • Disconnect the battery Prevents accidental starting of the engine.
  • Secure the combine Use jack stands or blocks to support the combine safely.
  • Wear PPE Protect yourself from potential hazards.
  • Refer to the service manual Always consult your combine's service manual for specific instructions and safety guidelines.

Tools and Materials Needed

Before starting the replacement process, gather the necessary tools and materials

  • New straw walker cranks (e.g., New Holland part number 84475611)
  • Socket set
  • Wrench set
  • Torque wrench
  • Hammer
  • Punch
  • Bearing puller (if necessary)
  • Grease gun and grease
  • Penetrating oil
  • Service manual for your combine model
  • Work gloves
  • Safety glasses

Step-by-Step Straw Walker Bearing and Crank Replacement

  1. Access the Straw Walker Access procedures vary based on the machine's design. Usually, you will need to remove access panels or shields to reach the straw walker assembly. Consult your service manual for specific instructions. Often, this involves removing the clean grain elevator or other components obstructing access.
  2. Inspect the Components Before disassembly, carefully inspect the bearings and cranks for any signs of wear or damage. Note the location of any worn parts.
  3. Remove the Old Bearings Use a socket or wrench to remove the bolts securing the bearing housings. If the bearings are stuck, apply penetrating oil and use a bearing puller for removal. Be careful not to damage the surrounding components.
  4. Remove the Old Cranks Typically, cranks are connected via bolted joints. Remove the bolts and carefully extract the crank. If the crank is seized, use penetrating oil and gentle hammering to loosen it. Mark the position of the cranks before removal to ensure proper alignment during reassembly.
  5. Clean the Mounting Surfaces Thoroughly clean the mounting surfaces where the new bearings and cranks will be installed. Remove any rust, debris, or old grease.
  6. Install the New Cranks Install the new cranks in the same position as the old ones. Ensure they are properly aligned. Torque the bolts to the manufacturer's specified torque. Typically, torque specifications range from 50-75 ft-lbs for 1/2" bolts, but always consult your service manual.
  7. Install the New Bearings Apply grease to the new bearings and install them into the bearing housings. Align the housings and secure them with the bolts. Torque the bolts to the manufacturer's specified torque. For example, a John Deere combine 9600 series straw walker bearing mounting bolt should be torqued to 65 ft-lbs.
  8. Grease the Bearings Use a grease gun to lubricate the new bearings. Ensure they are adequately greased according to the manufacturer's recommendations.
  9. Reassemble and Test Reinstall any removed access panels or shields. Reconnect the battery. Start the combine and run it at low speed to check for proper operation. Listen for any unusual noises or vibrations. Gradually increase the speed and continue monitoring for any issues.

Troubleshooting Tips

  • Stuck Bearings If the bearings are difficult to remove, apply penetrating oil and use a bearing puller. Heat can also be used to expand the bearing housing, making removal easier.
  • Misalignment Ensure the cranks are properly aligned during installation. Misalignment can cause excessive vibration and premature wear.
  • Incorrect Torque Always use a torque wrench to tighten the bolts to the manufacturer's specified torque. Over-tightening can damage the bolts or bearing housings, while under-tightening can cause the bolts to loosen during operation.

Maintaining Straw Walkers for Longevity

Regular maintenance can significantly extend the life of your combine's straw walker components. Consider the following practices

  • Regular Greasing Lubricate the bearings regularly according to the manufacturer's recommendations. Use high-quality grease designed for agricultural machinery.
  • Inspection Inspect the straw walker components regularly for any signs of wear or damage. Address any issues promptly to prevent further damage.
  • Proper Storage When storing the combine for the off-season, protect the straw walker from moisture and debris. Apply a rust inhibitor to prevent corrosion.

Remember to check other related components as part of your maintenance routine. Examine the combine belts driving the straw walkers and ensure they are in good condition. Similarly, inspect the combine concave as it works in tandem with the straw walkers to maximize grain separation.

Finding the Right Parts at Madison Tractor Company

At Madison Tractor Company, we understand the importance of keeping your combine running smoothly and efficiently. We offer a wide selection of high-quality straw walker bearings and cranks for all major combine brands, including John Deere, Case IH, New Holland, Gleaner, Massey Ferguson, Kubota, Allis Chalmers, Deutz, International Harvester, Oliver, White, Vermeer, Hesston, Mahindra Zetor. Whether you need a new bearing, crank, or other combine part, we have you covered.

In addition to straw walker components, we also stock a complete range of other combine parts, including radiators, water pumps, starters, alternators, hydraulic pumps, cylinders, clutch kits, PTO parts, fuel pumps, carburetors, injectors, filters, gaskets, pistons, seals, chains, concaves sickle sections. Our knowledgeable staff is always available to assist you in finding the right parts for your specific combine model.

Shop our extensive inventory today and experience the Madison Tractor Company difference! Get back to harvesting with confidence.

🔍 Can't Find Your Part?

Use our AI-Powered Part Finder to search by your equipment's make, model, and what you need. It's the fastest way to find the exact part for your machine.

Try the Part Finder →