John Deere 4440 Hydraulic System: Pump, Filter & Capacity
The John Deere 4440 tractor relies on a robust hydraulic system for various functions. This guide covers the hydraulic pump, filter, fluid specifications, and maintenance tips to keep your 4440 operating smoothly. Find the parts you need at Madison Tractor.
Introduction to the John Deere 4440 Hydraulic System
The John Deere 4440, a workhorse of the 1970s and early 80s, relies heavily on its hydraulic system for everything from steering and braking to implement control and power take-off (PTO) operation. Understanding the components, maintenance requirements potential problems within this system is crucial for any 4440 owner. At Madison Tractor Company, we understand the importance of keeping your equipment running. We carry a wide range of parts for John Deere, Case IH, Ford, New Holland, Massey Ferguson, Kubota, Allis Chalmers, Deutz, International Harvester, Oliver, White, Gleaner, Vermeer, Hesston, Mahindra Zetor tractors and combines. This article will focus on the hydraulic pump, filter fluid capacity specific to the John Deere 4440 tractor.
Recommended Parts for This Guide
10 parts we recommend — in stock, ships fast, one-click add to cart.
🔍 Looking for a specific part? Try our AI Part Finder — tell it your equipment and what you need, and it will find matching parts instantly.
John Deere 4440 Hydraulic Pump
The hydraulic pump on the John Deere 4440 is typically a closed-center, variable-displacement axial piston pump. This type of pump delivers oil on demand, increasing efficiency and reducing heat buildup compared to older, open-center systems. The pump is responsible for generating the hydraulic pressure needed to operate various functions.
Pump Location and Identification
The hydraulic pump is generally located on the right side of the engine, driven directly by the engine crankshaft or through a gear train. Identifying the pump is essential when ordering replacement parts. While specific OEM part numbers can vary based on the year and exact configuration of your 4440, a common part number to investigate is. Always verify compatibility with your tractor's serial number before ordering. Also see John Deere Tractor Hydraulic Pump: OEM Part Numbers for more details.
Pump Operation and Troubleshooting
The pump's variable displacement design means it only delivers the amount of oil needed at any given time. When no hydraulic functions are being used, the pump delivers a minimal amount of oil, just enough to maintain system pressure. When a hydraulic function is activated (e.g., raising the loader), the pump increases its output to meet the demand. Common problems with the hydraulic pump
- Low Hydraulic Pressure This can be caused by a worn pump, internal leaks, or a faulty pressure relief valve.
- No Hydraulic Pressure This could be due to a complete pump failure, a broken drive coupling, or a blocked suction line.
- Excessive Noise This often indicates cavitation within the pump, usually caused by a restricted suction line or low fluid level.
- Overheating Worn components or internal leaks within the pump can cause excessive heat generation.
Troubleshooting Tip A simple pressure test using a hydraulic pressure gauge can help diagnose pump problems. Connect the gauge to a test port on the hydraulic system and check the pressure reading against the specifications in the John Deere 4440 technical manual. Also check for leaks around the pump and hydraulic lines. For related parts, check out our selection of John Deere tractor parts.
Replacing the Hydraulic Pump
Replacing the hydraulic pump is a significant repair. Consult the John Deere 4440 service manual for detailed instructions. Here's a general overview
- Safety First Disconnect the battery and relieve all hydraulic pressure.
- Drain the Hydraulic Oil Place a large drain pan under the tractor and remove the drain plug.
- Disconnect Hydraulic Lines Carefully disconnect all hydraulic lines connected to the pump. Cap or plug the lines to prevent contamination.
- Remove the Pump Unbolt the pump from the engine and carefully remove it.
- Install the New Pump Install the new hydraulic pump overhaul kit, ensuring proper alignment and torqueing the bolts to the correct specifications.
- Reconnect Hydraulic Lines Reconnect all hydraulic lines, ensuring they are properly tightened.
- Refill the Hydraulic Oil Refill the hydraulic system with the correct type and amount of hydraulic fluid (see below).
- Bleed the System Bleed any air from the hydraulic system according to the service manual.
- Test the System Start the tractor and test all hydraulic functions to ensure they are working properly.
When performing pump maintenance or an overhaul, remember to inspect components such as the hydraulic pump valve seat insert and valve springs, or consider a full seal kit for minor repairs. For more extensive repairs, a bearing and race replacement, or new pistons and their springs, might be necessary.
Safety Warning Hydraulic fluid is under high pressure and can cause serious injury. Always relieve pressure before disconnecting any hydraulic lines.
John Deere 4440 hydraulic filter
The hydraulic filter is critical for maintaining the cleanliness of the hydraulic fluid. A clean filter prevents contaminants from circulating through the system, which can cause wear and damage to hydraulic components like pumps, valves cylinders. Madison Tractor Company carries a range of high-quality hydraulic filters, including cartridge filters, for John Deere and other brands. Regular filter replacement is far cheaper than replacing a hydraulic pump or repairing a damaged cylinder. Check out our Tractor Hydraulic Filter: Cross Reference by Brand article for help finding the right filter for your 4440.
Filter Location and Replacement
On the John Deere 4440, the hydraulic filter is typically located near the hydraulic reservoir, often under the cab or near the rear axle. The exact location may vary slightly depending on the tractor's configuration. To replace the filter
- Locate the Filter Identify the hydraulic filter housing.
- Prepare for Spillage Place a drain pan under the filter to catch any spilled oil.
- Unscrew the Filter Unscrew the old filter from the housing. You may need a filter wrench.
- Lubricate the New Filter Lightly lubricate the rubber gasket on the new filter with hydraulic oil.
- Install the New Filter Screw the new filter onto the housing until the gasket makes contact, then tighten it an additional half to three-quarters of a turn, or according to the instructions on the filter.
- Check for Leaks Start the tractor and check for leaks around the filter.
Filter Maintenance Schedule
John Deere recommends replacing the hydraulic filter on the 4440 every 500 hours of operation, or at least annually. More frequent changes may be necessary if the tractor is operating in dusty or dirty conditions.
Filter Part Numbers
A common hydraulic filter part number for the John Deere 4440 is, however, always verify this with your tractor's serial number and parts manual to ensure compatibility.
John Deere 4440 Hydraulic Fluid Capacity
Using the correct type and amount of hydraulic fluid is essential for proper system operation and longevity. The John Deere 4440 typically requires approximately 12 gallons (45 liters) of hydraulic fluid. Always consult the operator's manual for the specific capacity and recommended fluid type for your tractor. John Deere Hy-Gard is a common and recommended hydraulic fluid for this model. Low fluid levels can lead to pump cavitation and overheating. Leaks in hydraulic lines can also lead to fluid loss, requiring replacement tractor hydraulic hoses.
Checking the Fluid Level
The hydraulic fluid level can be checked using a dipstick or sight gauge located on the hydraulic reservoir. The fluid level should be checked regularly, especially before extended use or heavy workloads.
Changing the Hydraulic Fluid
The hydraulic fluid should be changed every 1000 hours of operation or every two years, whichever comes first. To change the fluid
- Warm the Fluid Run the tractor for a few minutes to warm up the hydraulic fluid. This will help it flow more easily.
- Locate the Drain Plug Find the drain plug on the hydraulic reservoir.
- Place a Drain Pan Position a large drain pan under the drain plug.
- Remove the Drain Plug Remove the drain plug and allow the fluid to drain completely.
- Reinstall the Drain Plug Clean the drain plug and reinstall it, tightening it securely.
- Refill the System Refill the hydraulic system with the correct type and amount of hydraulic fluid.
- Check the Level Check the fluid level using the dipstick or sight gauge and add more fluid if necessary.
Hydraulic Cylinders and Hoses
While this article focuses on the hydraulic pump, filter capacity, remember that the John Deere 4440 utilizes several hydraulic cylinders and hoses. These are critical components for steering, implement control loader operation. Problems with cylinders or hoses can manifest as slow or jerky movement, leaks, or complete failure of a hydraulic function. Be sure to check out Tractor Hydraulic Cylinder: Steering, Lift & Loader and Tractor Hydraulic Hose: Sizing, Pressure Ratings & Fittings for more information on maintaining these components. Madison Tractor offers a wide selection of cylinders, hoses fittings for various tractor brands, including John Deere, Case IH more. Consider inspecting your tractor hydraulic cylinders and tractor hydraulic hoses regularly to ensure optimal hydraulic system performance.
Conclusion
Maintaining the hydraulic system on your John Deere 4440 is crucial for its reliable operation. By understanding the components, following the recommended maintenance schedule addressing problems promptly, you can keep your 4440 running smoothly for years to come. Madison Tractor Company is your trusted source for all your agricultural parts needs. Whether you need a replacement hydraulic pump, filter, hoses, cylinders, radiators, water pumps, starters, alternators, clutch kits, PTO parts, fuel pumps, carburetors, injectors, gaskets, pistons, bearings, seals, belts, chains, concaves, or sickle sections, we have you covered. Shop our extensive online catalog or contact our knowledgeable team for assistance in finding the right parts for your John Deere 4440 and other equipment. You can also use our AI-Powered Part Finder to search for parts by your specific make and model.
Part of our comprehensive guide
Tractor Hydraulic System Guide: Pumps, Cylinders & Troubleshooting

















