Skip to main content
(828) 649-7190
Same Day Shipping Before 2pm EST

Kubota Glow Plug Replacement: All Diesel Models

Struggling with hard starts on your Kubota diesel tractor? This guide provides a comprehensive walkthrough on replacing your glow plugs, covering common issues, troubleshooting, and step-by-step instructions. Ensure reliable starts and extend the life of your Kubota.

Kubota tractors, known for their reliability and durability, are a mainstay on farms and ranches. However, like any diesel engine, Kubota's rely on glow plugs for efficient cold starting. Over time, these glow plugs can wear out, leading to hard starts, excessive smoke reduced performance. This guide will walk you through the process of diagnosing and replacing glow plugs on your Kubota diesel tractor.

Recommended Parts for This Guide

6 parts we recommend — in stock, ships fast, one-click add to cart.

🔍 Looking for a specific part? Try our AI Part Finder — tell it your equipment and what you need, and it will find matching parts instantly.

Understanding Kubota Glow Plugs

Glow plugs are small heating elements located in the cylinder head near the injectors. When the engine is cold, these plugs heat the combustion chamber, allowing the diesel fuel to ignite more easily. Kubota glow plugs are designed to operate at a specific voltage and amperage. Using the wrong type can damage your engine or the glow plug system. Madison Tractor Company stocks a wide range of glow plugs for Kubota, John Deere, Case IH, Ford, New Holland, Massey Ferguson many other brands.

Symptoms of Failing Kubota Glow Plugs

Recognizing the symptoms of failing glow plugs is crucial for timely replacement and preventing further engine damage. Common signs

  • Hard Starting This is the most common symptom. The engine may crank for an extended period before starting, especially in cold weather.
  • Excessive White Smoke Unburnt fuel can cause white smoke during startup, indicating incomplete combustion due to insufficient heat.
  • Rough Idle The engine may idle roughly or stall shortly after starting, as the cylinders are not firing evenly.
  • Reduced Power In some cases, failing glow plugs can lead to a slight reduction in overall engine power.
  • Engine Misfires Intermittent misfires, particularly when the engine is cold, can also point to faulty glow plugs.

Diagnosing Kubota Glow Plug Problems

Before replacing your Kubota glow plugs, it's important to accurately diagnose the problem. Here are a few troubleshooting steps

  1. Visual Inspection Check the glow plugs for any signs of physical damage, such as cracks or swelling.
  2. Continuity Test Use a multimeter to test the continuity of each glow plug. A good glow plug should have low resistance (typically less than 2 ohms). A reading of infinite resistance indicates a failed glow plug.
  3. Voltage Test Use a multimeter to check for voltage at the glow plug harness when the ignition is turned on. No voltage indicates a problem with the wiring, relay, or timer.
  4. Individual Cylinder Test If you suspect only one or two glow plugs are failing, you can disconnect them one at a time and try starting the engine. If the starting improves after disconnecting a particular glow plug, that plug is likely faulty.

If you are experiencing starting issues, also check your Kubota tractor starter to ensure it's operating correctly, as a weak starter can exacerbate starting problems.

Tools and Materials Needed for Kubota Glow Plug Replacement

Before starting the replacement process, gather the necessary tools and materials

  • New Kubota glow plugs (ensure they are the correct type for your model)
  • Socket set with extensions
  • Wrench set
  • Multimeter
  • Wire brush
  • Penetrating oil
  • Torque wrench
  • Dielectric grease
  • Safety glasses
  • Gloves

Step-by-Step Kubota Glow Plug Replacement Guide

Follow these steps to safely and effectively replace your Kubota glow plugs

  1. Safety First Disconnect the negative battery cable to prevent electrical shorts.
  2. Locate the Glow Plugs The glow plugs are typically located on the side of the engine, near the fuel injectors. Refer to your Kubota's service manual for the exact location.
  3. Apply Penetrating Oil Spray penetrating oil onto the base of the glow plugs and let it soak for at least 15 minutes. This will help loosen any corrosion and make removal easier.
  4. Disconnect the Wiring Carefully disconnect the wiring harness from each glow plug.
  5. Remove the Glow Plugs Use the correct size socket and extension to remove the glow plugs. Be careful not to overtighten or strip the threads. If a glow plug is particularly difficult to remove, apply more penetrating oil and let it soak longer.
  6. Clean the Threads Use a wire brush to clean the threads in the cylinder head. This will ensure proper seating of the new glow plugs.
  7. Apply Dielectric Grease Apply a small amount of dielectric grease to the threads of the new glow plugs. This will help prevent corrosion and make future removal easier.
  8. Install the New Glow Plugs Carefully thread the new glow plugs into the cylinder head. Tighten them to the manufacturer's specified torque using a torque wrench. Typical torque specification for Kubota glow plugs is 11-15 ft-lbs (15-20 Nm). Always consult your Kubota service manual for the specific torque specification for your model.
  9. Reconnect the Wiring Reconnect the wiring harness to each glow plug.
  10. Reconnect the Battery Reconnect the negative battery cable.
  11. Test the Engine Start the engine and observe its performance. It should start more easily and run smoother, especially in cold weather.

Safety Warning Always allow the engine to cool completely before attempting to replace the glow plugs. Working on a hot engine can cause burns and damage to the engine components. Never use excessive force when removing the glow plugs, as this can damage the cylinder head. If a glow plug is stuck, consult a qualified mechanic.

Specific Kubota Models and Glow Plug Part Numbers

While this is a general guide, specific Kubota models may have slight variations. Here are some common models and potential OEM glow plug part numbers (always verify with your parts manual)

  • Kubota B Series (e.g., B2320, B2650, B26) Often uses glow plug part number 16851-65512 or 16851-65510
  • Kubota L Series (e.g., L3901, L2501, L3301) Often uses glow plug part number 19420-65510
  • Kubota M Series (e.g., M7040, M9540) Glow plug part numbers can vary; consult your manual.

Remember to cross-reference these part numbers with your specific Kubota model and year using your parts manual or by contacting Madison Tractor Company's expert parts staff. For common engine types, consider our glow plug for V3300 IDI engines, a glow plug for V2003-V2203 IDI engines, or a glow plug for V1702 engines. We can also help you find other essential parts like filters and radiators.

Glow Plug Relays and Timers

The glow plug system includes a relay and timer that control the duration of glow plug activation. A functioning glow plug indicator is also vital to signal when the glow plugs are preheating. If your glow plugs are functioning properly but you're still experiencing starting problems, the relay or timer may be faulty. Use a multimeter to test the relay and timer according to your Kubota's service manual. Replace these components if necessary.

Preventing Future Glow Plug Problems

Here are a few tips to help extend the life of your Kubota glow plugs

  • Use High-Quality Fuel Using clean, high-quality diesel fuel can help prevent carbon buildup on the glow plugs.
  • Regular Maintenance Follow your Kubota's recommended maintenance schedule, including regular oil changes and filter replacements. Check and clean battery terminals.
  • Avoid Excessive Cranking Avoid excessive cranking when starting the engine, as this can overheat the glow plugs.
  • Proper Storage Store your Kubota in a dry place to prevent corrosion.

Remember to also check other essential electrical components like your John Deere tractor alternator or Ford tractor starter to ensure your tractor's electrical system is functioning correctly. We also carry parts for Case IH, Massey Ferguson, Allis Chalmers, Deutz, International Harvester, Oliver, White, Gleaner, Vermeer, Hesston, Mahindra Zetor.

Shop Kubota Parts at Madison Tractor Company

Madison Tractor Company is your trusted source for high-quality Kubota parts, including glow plugs, starters, alternators more. We carry a wide selection of parts for all major tractor brands, including John Deere, Case IH, Ford, New Holland Massey Ferguson. Our knowledgeable staff is here to help you find the right parts for your needs and get your tractor back up and running quickly. Browse our online catalog today for Kubota glow plugs, or contact us for expert assistance! You can also use our AI-Powered Part Finder to search for parts by your specific make and model.