Skip to main content
(828) 649-7190
Same Day Shipping Before 2pm EST

Briggs & Stratton Valve Cover Gasket Replacement

A leaking valve cover gasket can cause oil leaks and performance issues in your Briggs & Stratton engine. This guide walks you through replacing the gasket, saving you time and money. Learn the tools you'll need and step-by-step instructions.

Is Your Briggs & Stratton valve cover gasket Leaking?

A leaky valve cover gasket on your Briggs & Stratton engine is a common problem, especially as the engine ages. These gaskets are responsible for sealing the valve cover to the engine block, preventing oil from escaping. Over time, the gasket can become brittle, cracked, or warped due to heat and pressure, leading to leaks. Spotting the issue early can prevent more serious engine damage.

🔍 Looking for a specific part? Try our AI Part Finder — tell it your equipment and what you need, and it will find matching parts instantly.

Here are some telltale signs that your briggs valve cover gasket needs replacing:

  • Visible Oil Leaks: The most obvious sign is oil pooling around the valve cover, running down the engine, or dripping onto the ground.
  • Oil Smell: You might notice a distinct burning oil smell, especially after the engine has been running for a while. This is because oil is leaking onto hot engine components.
  • Low Oil Level: Regularly check your engine oil level. If you notice it's consistently lower than usual, even after topping it off, a leaky valve cover gasket could be the culprit.
  • Dirty Engine: Excessive oil around the valve cover attracts dirt and debris, making the engine look grimy.
  • Engine Performance Issues: In severe cases, a significant oil leak can lead to low oil pressure, which can negatively affect engine performance.

If you observe any of these symptoms, it's time to inspect and potentially replace your valve cover gasket.

Tools and Materials You'll Need

Before you start, gather the necessary tools and materials:

  • New Briggs & Stratton Valve Cover Gasket: Make sure you get the correct gasket for your specific engine model. Check your engine's model, type, and code, often stamped on the valve cover itself. You can find the right replacement valve cover gasket at Madison Tractor.
  • Socket Set and Wrenches: You'll need sockets and wrenches to remove the valve cover bolts. Metric sizes are common for Briggs & Stratton engines.
  • Screwdrivers: Both flathead and Phillips screwdrivers may be needed to remove any obstructing components or fasteners.
  • Torque Wrench: Essential for tightening the valve cover bolts to the correct specification, preventing leaks and damage.
  • Scraper or Putty Knife: For cleaning old gasket material from the engine block and valve cover.
  • Cleaning Supplies: Brake cleaner or carburetor cleaner to remove oil and grime from the mating surfaces. Also, clean shop rags. You might need a briggs and stratton carburetor cleaning after this job, as debris can accumulate.
  • Oil Drain Pan: To catch any oil that may spill during the process.
  • Gloves: To protect your hands from oil and chemicals.
  • Safety Glasses: To protect your eyes.

Having these tools on hand will make the briggs valve cover gasket replacement process smoother and more efficient.

Step-by-Step Valve Cover Gasket Replacement

Follow these steps to replace your Briggs & Stratton valve cover gasket:

  1. Safety First: Disconnect the spark plug wire from the spark plug to prevent accidental starting. Let the engine cool completely before beginning.
  2. Prepare the Area: Clean the area around the valve cover with a brush and cleaner to remove any loose dirt and debris. This prevents contaminants from entering the engine.
  3. Remove Obstructing Components: Depending on the engine model, you may need to remove air filters, fuel lines (carefully, clamp them first!), or other components that block access to the valve cover. Note their positions or take photos for easy reassembly. Refer to our articles on small engine fuel pump replacement if you need to remove the fuel pump.
  4. Remove the Valve Cover: Use the appropriate socket or wrench to loosen and remove the valve cover bolts. Work carefully, as some bolts may be tight or corroded. Gently tap the valve cover with a rubber mallet if it's stuck.
  5. Clean the Mating Surfaces: Thoroughly clean the valve cover and engine block mating surfaces with a scraper or putty knife to remove all traces of the old gasket. Be careful not to scratch or damage the metal surfaces. Use brake cleaner to remove any remaining oil or grime.
  6. Install the New Gasket: Position the new briggs valve cover gasket onto the valve cover. Ensure it sits correctly in the groove (if applicable) and aligns with the bolt holes. Some gaskets may have a specific orientation, so double-check.
  7. Reinstall the Valve Cover: Carefully place the valve cover back onto the engine block, aligning the bolt holes.
  8. Tighten the Bolts: Install the valve cover bolts and tighten them in a crisscross pattern to ensure even pressure on the gasket. Use a torque wrench to tighten the bolts to the manufacturer's specified torque. Over-tightening can damage the gasket or the valve cover.
  9. Reassemble Components: Reinstall any components you removed in step 3, such as air filters or fuel lines.
  10. Reconnect Spark Plug: Reconnect the spark plug wire.
  11. Check for Leaks: Start the engine and let it run for a few minutes. Carefully inspect the valve cover area for any signs of leaks. If you see any leaks, stop the engine, let it cool down, and re-torque the bolts, ensuring they are tightened evenly.

Important Considerations and Tips

  • Torque Specifications: Always use the correct torque specifications for the valve cover bolts. You can usually find these in the engine's service manual or online.
  • Gasket Type: Some gaskets are designed to be installed dry, while others may require a sealant. Check the manufacturer's instructions.
  • Bolt Condition: Inspect the valve cover bolts for damage or corrosion. Replace them if necessary.
  • Valve Cover Condition: Check the valve cover for cracks or warping. Replace it if needed.
  • Preventative Maintenance: Regular engine maintenance, including oil changes and air filter replacements, can help extend the life of your valve cover gasket. Don't forget to check your briggs head gasket during your maintenance routine.

Common Machines That Use Briggs & Stratton Engines

Briggs & Stratton engines are found in a wide variety of outdoor power equipment, including:

  • Lawn Mowers: Push mowers, riding mowers (including those from John Deere, Craftsman, Cub Cadet, Husqvarna, and Toro), and zero-turn mowers (from brands like Hustler, Scag, Exmark, Ferris, and Dixie Chopper) often utilize Briggs & Stratton engines.
  • Snow Blowers: Many snow blowers from Ariens, Toro, and other manufacturers are powered by Briggs & Stratton engines. Remember to check your shear pins!
  • Generators: Portable generators and standby generators frequently use Briggs & Stratton engines for reliable power.
  • Pressure Washers: Many pressure washers rely on Briggs & Stratton engines for their power.
  • Tillers: Garden tillers often use Briggs & Stratton engines for tilling soil.

Madison Tractor carries a wide range of parts for these machines, including belts, blades, spindles, pulleys, filters, spark plugs, and bearings. We also carry briggs carburetor rebuild kit parts. No matter what you need, we can help you keep your equipment running smoothly.

Troubleshooting Valve Cover Leaks

Even after replacing the gasket, you might still experience leaks. Here are some possible causes:

  • Incorrect Torque: Double-check that you tightened the bolts to the correct torque specification.
  • Damaged Valve Cover: Inspect the valve cover for cracks or warping.
  • Improperly Cleaned Surfaces: Ensure the mating surfaces are completely clean and free of debris.
  • Incorrect Gasket: Make sure you're using the correct gasket for your engine model.
  • Engine Issues: Excessive crankcase pressure can also cause leaks. Address any underlying engine issues.

Shop Briggs & Stratton Parts at Madison Tractor

Keeping your Briggs & Stratton engine running smoothly is essential for reliable performance. At Madison Tractor, we offer a wide selection of genuine Briggs & Stratton parts, including valve cover gaskets, carburetors (check out our article on kohler carburetor replacement too!), air filters, oil filters, spark plugs, and more. We also stock parts for other major brands like Kohler and Kawasaki. Find the parts you need to keep your John Deere, Craftsman, Cub Cadet, Husqvarna, Toro, Ariens, Murray, Hustler, Scag, Exmark, Ferris, Snapper, Simplicity, or Dixie Chopper equipment in top condition. Shop our selection of Briggs & Stratton parts today!

🔍 Can't Find Your Part?

Use our AI-Powered Part Finder to search by your equipment's make, model, and what you need. It's the fastest way to find the exact part for your machine.

Try the Part Finder →

Here are parts available from Madison Tractor that fit your equipment: