Allis Chalmers Hydraulic Pump: WD45, D17 & 190
A comprehensive guide to diagnosing, repairing, and replacing the hydraulic pump on your Allis Chalmers tractor. Covers common issues, troubleshooting tips, and models like the WD45, D17, and 190. Find the Allis Chalmers hydraulic pump you need at Madison Tractor.
Introduction to Allis Chalmers Hydraulic Pumps
The hydraulic system on your Allis Chalmers tractor is crucial for tasks like lifting implements, steering, and operating loaders. A properly functioning hydraulic pump is the heart of this system. This guide covers common issues, troubleshooting steps, and replacement options for Allis Chalmers hydraulic pumps, focusing on popular models like the WD45, D17, and 190. At Madison Tractor, we understand the importance of keeping your Allis Chalmers running smoothly, which is why we stock a wide range of hydraulic parts, including pumps, cylinders, and hoses.
Recommended Parts for This Guide
7 parts we recommend — in stock, ships fast, one-click add to cart.
🔍 Looking for a specific part? Try our AI Part Finder — tell it your equipment and what you need, and it will find matching parts instantly.
Understanding Your Allis Chalmers Hydraulic System
Before diving into troubleshooting, it's helpful to understand the basics. Allis Chalmers tractors typically use a gear-type hydraulic pump driven directly by the engine. This pump draws hydraulic fluid from the reservoir (usually located in the transmission housing) and pressurizes it, sending it to various hydraulic components. Make sure you check out our Tractor Hydraulic Hose: Sizing, Pressure Ratings & Fittings guide for selecting and maintaining hoses.
Common components include:
- Hydraulic Pump: The source of hydraulic pressure.
- Hydraulic Reservoir: Holds the hydraulic fluid.
- Control Valves: Direct the flow of hydraulic fluid to different circuits.
- Hydraulic Cylinders: Convert hydraulic pressure into linear motion (e.g., for lifting implements).
- Hydraulic Hoses and Lines: Carry the fluid between components.
- hydraulic filter: Removes contaminants from the fluid. Regularly replacing your hydraulic filter is crucial. Consult our Tractor Hydraulic Filter: Cross Reference by Brand article to find the right replacement.
Common Allis Chalmers Hydraulic Pump Problems
Several issues can plague your Allis Chalmers hydraulic pump. Recognizing the symptoms is the first step in diagnosing the problem.
- Low Hydraulic Pressure: This can result in slow or weak lifting, difficulty steering, or inoperable implements.
- No Hydraulic Pressure: Complete failure of the hydraulic system.
- Erratic Hydraulic Operation: Jerky movements, inconsistent pressure, or intermittent functionality.
- Excessive Noise: Whining, grinding, or squealing noises from the pump can indicate wear or damage, or a failing bearing.
- Overheating Hydraulic Fluid: Can be caused by a failing pump, restricted flow, or contaminated fluid.
Troubleshooting Your Allis Chalmers Hydraulic Pump
Before replacing your Allis Chalmers hydraulic pump, try these troubleshooting steps:
1. Check the Hydraulic Fluid Level and Condition
Low fluid level is a common cause of hydraulic problems. Check the reservoir and top off with the correct type of hydraulic fluid. Inspect the fluid for contamination (water, dirt, or metal particles). Milky or discolored fluid indicates water contamination. If the fluid is dirty, drain and flush the system, and replace the hydraulic filter.
2. Inspect the Hydraulic Filter
A clogged hydraulic filter can restrict flow and reduce pressure. Replace the filter with a new one. Consult your tractor's manual for the correct filter type. Madison Tractor carries a wide variety of filters for Allis Chalmers tractors. Refer to our Tractor Hydraulic Filter: Cross Reference by Brand article to find the right replacement.
3. Check for Leaks
Inspect all hydraulic lines, hoses, and fittings for leaks. Tighten any loose connections. Replace damaged hoses or lines. Don't forget to check the hydraulic cylinders themselves for leaks, as covered in our guide to Tractor Hydraulic Cylinder: Steering, Lift & Loader.
4. Pressure Testing the Hydraulic Pump
A pressure test will confirm if the pump is producing adequate pressure. You'll need a hydraulic pressure gauge and adapter fittings. Consult your tractor's service manual for the correct testing procedure and pressure specifications. For an Allis Chalmers D17, you should typically see around 1800-2000 PSI at the test port with the engine at operating speed.
- Connect the pressure gauge to the test port on the hydraulic system.
- Start the tractor and let it warm up to operating temperature.
- Engage the hydraulic system (e.g., raise the 3-point hitch).
- Read the pressure gauge.
If the pressure is below the specified range, the pump may be worn or damaged. For pumps like the triple 70248735, a repair kit might be a cost-effective solution.
SAFETY WARNING: Hydraulic fluid is under high pressure. Always relieve pressure before disconnecting any hydraulic lines or fittings. Hydraulic injection injuries can be serious. Seek immediate medical attention if hydraulic fluid penetrates your skin.
5. Check the Relief Valve
The hydraulic relief valve protects the system from overpressure. If the relief valve is stuck open, it will bypass fluid and reduce pressure. Locate the relief valve (usually on the control valve assembly) and inspect it for damage or debris. A temporary fix might involve carefully cleaning the valve, but replacement is often the best solution.
Replacing Your Allis Chalmers Hydraulic Pump
If troubleshooting indicates a faulty pump, replacement is necessary. Here's a general overview of the replacement process:
- Safety First: Disconnect the battery to prevent accidental starting.
- Drain the Hydraulic Fluid: Drain the fluid from the reservoir. Dispose of used fluid properly.
- Disconnect Hydraulic Lines: Disconnect the hydraulic lines from the pump. Cap the lines to prevent contamination.
- Remove the Old Pump: Unbolt the pump from the tractor. Note the orientation of the pump and any shims or spacers.
- Install the New Pump: Install the new pump, ensuring proper alignment. Use new gaskets or seals.
- Connect Hydraulic Lines: Reconnect the hydraulic lines to the pump. Tighten the fittings to the specified torque.
- Refill the Hydraulic Fluid: Refill the reservoir with the correct type and amount of hydraulic fluid.
- Bleed the System: Bleed the air from the hydraulic system. Consult your tractor's service manual for the proper bleeding procedure.
- Test the System: Start the tractor and test the hydraulic system. Check for leaks and proper operation.
Typical Allis Chalmers hydraulic pump torque specs (always verify in your service manual): Mounting bolts: 30-40 ft-lbs; Hydraulic line fittings: 20-30 ft-lbs.
Specific Model Considerations
- Allis Chalmers WD45: The WD45 often uses a relatively simple gear pump. Check the drive coupling for wear. A common OEM part number cross-reference for the hydraulic pump is 70230122 or 70230122R.
- Allis Chalmers D17: The D17 may have different pump configurations depending on the year and options. Be sure to verify the correct pump for your specific tractor. Early D17 models may use a different pump than later series.
- Allis Chalmers 190: The 190 is a larger tractor with a higher-capacity hydraulic system. Ensure the replacement pump meets the flow and pressure requirements of your 190.
Hydraulic Pump Options & Brands
Madison Tractor carries hydraulic pumps for a wide range of tractors, including John Deere, Case IH, Ford, New Holland, Massey Ferguson, Kubota, Allis Chalmers, Deutz, International Harvester, Oliver, White, Gleaner, Vermeer, Hesston, Mahindra, and Zetor.
Beyond hydraulic pumps, Madison Tractor also offers a wide selection of parts like radiators, water pumps, starters, alternators, hydraulic cylinders, clutch kits, PTO parts, fuel pumps, carburetors, injectors, filters, gaskets, pistons, bearings, seals, belts, chains, concaves, and sickle sections. If you need a clutch kit for your Allis Chalmers, we can help.
Conclusion
Maintaining your Allis Chalmers hydraulic system is crucial for reliable operation. By understanding the system, recognizing common problems, and following proper troubleshooting steps, you can keep your tractor running smoothly for years to come. When it's time for replacement parts, Madison Tractor is your trusted source for quality Allis Chalmers parts and expert advice. Whether it's a hydraulic pump, cylinder or other component, we have you covered.
Ready to get your Allis Chalmers back in action? Shop our wide selection of Allis Chalmers hydraulic pumps and other parts at Madison Tractor today!
🔍 Can't Find Your Part?
Use our AI-Powered Part Finder to search by your equipment's make, model, and what you need. It's the fastest way to find the exact part for your machine.
Try the Part Finder →Part of our comprehensive guide
Tractor Hydraulic System Guide: Pumps, Cylinders & Troubleshooting














