Skip to main content
(828) 649-7190
Same Day Shipping Before 2pm EST

Cub Cadet RZT Belt Replacement: RZT 50, RZT 42

Replacing a worn or broken mower deck belt on your Cub Cadet RZT 50 or RZT 42 is a common maintenance task. This guide provides step-by-step instructions, safety tips, and part recommendations to help you get the job done right.

Introduction to Cub Cadet RZT Belt Replacement

If you own a Cub Cadet RZT 50 or RZT 42 zero-turn mower, you're likely familiar with the importance of regular maintenance. A key component of your mower's performance is the mower deck belt, which transmits power from the engine to the blades. Over time, this belt can wear, crack, or even break, leading to decreased cutting performance or complete mower shutdown. This guide will walk you through the process of replacing the mower deck belt on your Cub Cadet RZT 50 or RZT 42, helping you get back to maintaining your lawn with confidence.

Recommended Parts for This Guide

10 parts we recommend — in stock, ships fast, one-click add to cart.

🔍 Looking for a specific part? Try our AI Part Finder — tell it your equipment and what you need, and it will find matching parts instantly.

Before we begin, remember that safety is paramount. Always disconnect the spark plug wire(s) before working on your mower. This prevents accidental starting and potential injury. Refer to your owner's manual for specific safety instructions related to your model.

Here at Madison Tractor Company, we understand the importance of having the right parts for the job. We carry a wide selection of replacement belts for Cub Cadet, John Deere, Craftsman, Husqvarna, Toro, Ariens, and many other brands. Let’s get started!

Identifying the Correct Cub Cadet RZT Belt

Before you begin, ensure you have the correct replacement belt. Using the wrong size or type of belt can lead to poor performance and premature wear. The correct belt size can usually be found in your owner's manual. You can also use your mower's model number to search for compatible belts on our website or at your local parts store.

For the Cub Cadet RZT 50 and RZT 42, deck belt sizes can vary slightly depending on the year of manufacture. Consulting your owner's manual or using a parts lookup tool is the best way to ensure you get the correct belt. However, here are a couple of common part numbers and sizes:

  • RZT 50: Refer to your manual, but a common replacement is a 5/8" x 143" belt.
  • RZT 42: Refer to your manual, but a common replacement is a 5/8" x 95" belt.

If you’re unsure, it’s always better to measure your old belt (if possible) or contact us at Madison Tractor Company for assistance. We can help you find the correct Cub Cadet replacement part.

While you're at it, consider inspecting other wear items like blades and spindles. Replacing these at the same time can save you time and effort in the long run.

Tools and Materials Needed

Here's a list of tools and materials you'll need for the Cub Cadet RZT belt replacement:

  • New mower deck belt (ensure it's the correct size)
  • Socket wrench set
  • Wrench set
  • Pliers
  • Screwdrivers (Phillips and flathead)
  • Gloves
  • Safety glasses
  • Jack (optional, but highly recommended for easier access)
  • Wheel chocks (if using a jack)
  • Pen and paper or camera (to document belt routing)

Step-by-Step Cub Cadet RZT Belt Replacement

Follow these steps to replace the mower deck belt on your Cub Cadet RZT 50 or RZT 42:

  1. Safety First: Disconnect the spark plug wire(s) and secure them away from the spark plug(s). Engage the parking brake.
  2. Prepare the Mower: If you're using a jack, chock the rear wheels for safety. Carefully jack up the front of the mower to provide better access to the deck. Never work under a mower supported only by a jack – use jack stands for added safety.
  3. Remove the Mower Deck: Most Cub Cadet RZT mowers have a lever or handle that disengages the deck. Refer to your owner's manual for the specific procedure. Once disengaged, carefully slide the deck out from under the mower.
  4. Inspect the Old Belt and Pulleys: Before removing the old belt, take a picture or draw a diagram of the belt routing. This will be invaluable when installing the new belt. Inspect the pulleys for wear, damage, or debris. Clean them thoroughly with a wire brush. Replace any worn or damaged pulleys for optimal performance.
  5. Remove the Old Belt: Using your wrench or socket set, loosen the tension on the idler pulley(s). This will allow you to slip the old belt off the pulleys. Work the belt off each pulley, carefully noting its path.
  6. Install the New Belt: Using your diagram or picture as a guide, route the new belt around all the pulleys. Ensure the belt is properly seated in the grooves of each pulley. Pay close attention to the direction of the belt (if applicable).
  7. Tension the Belt: Once the belt is in place, re-engage the tension on the idler pulley(s). The belt should be snug but not overly tight. Refer to your owner's manual for the correct belt tension specifications.
  8. Reinstall the Mower Deck: Carefully slide the mower deck back under the mower and re-engage the deck lift mechanism.
  9. Test the Mower: Reconnect the spark plug wire(s). Start the mower and engage the mower deck. Listen for any unusual noises and ensure the blades are rotating smoothly. If everything sounds and looks good, you've successfully replaced the mower deck belt.

Common Problems and Solutions

  • Belt Slippage: If the belt is slipping, it may be too loose. Check the belt tension and adjust as needed. Also, inspect the pulleys for wear or damage. A worn pulley can cause the belt to slip even if it's properly tensioned.
  • Belt Noise: A squealing or chirping noise could indicate a worn belt, a misaligned pulley, or a dry bearing in one of the pulleys or spindles. Inspect all components and lubricate or replace as needed.
  • Belt Breaking Prematurely: This could be caused by a damaged pulley, excessive belt tension, or using the wrong belt type. Ensure you're using the correct belt and that all pulleys are in good condition.
  • Difficulty Removing or Installing the Belt: Make sure the tension is fully released on the idler pulley. Sometimes, a little wiggling and maneuvering are required to get the belt around tight corners.

Remember to check out our guides on John Deere mower deck belt replacement, Craftsman 42-inch mower belt replacement and Husqvarna mower belt size guides for more in-depth information.

Also, check out the Cub Cadet deck belt replacement guide for general information and models outside the RZT 42 & 50.

Maintenance Tips for Cub Cadet RZT Belts

To extend the life of your mower deck belt, follow these maintenance tips:

  • Keep the Deck Clean: Regularly clean the mower deck to remove grass clippings and debris. This will prevent the buildup of moisture and corrosion, which can damage the belt and pulleys.
  • Inspect the Belt Regularly: Check the belt for cracks, fraying, or other signs of wear. Replace the belt immediately if you notice any damage.
  • Maintain Proper Belt Tension: Ensure the belt is properly tensioned according to the manufacturer's specifications.
  • Avoid Overloading the Mower: Don't try to cut grass that is too tall or thick, as this can put excessive strain on the belt.
  • Store the Mower Properly: When storing the mower for the off-season, loosen the belt tension to prevent it from stretching or cracking.

When to Consider Professional Help

While replacing a mower deck belt is a relatively straightforward task, there are times when it's best to seek professional help. If you're not comfortable working on your mower, or if you encounter any problems during the replacement process, contact a qualified mechanic. They have the expertise and tools to diagnose and repair any issues quickly and efficiently.

Additionally, if you suspect there may be underlying issues with your mower, such as a worn spindle bearing or misaligned pulleys, it's best to have a professional inspect the mower to prevent further damage.

Madison Tractor Company: Your Trusted Parts Supplier

At Madison Tractor Company, we're committed to providing our customers with high-quality replacement parts and exceptional service. We carry a wide selection of belts, blades, spindles, pulleys, filters, spark plugs, bearings, shear pins, and other parts for all major brands of outdoor power equipment, including John Deere, Craftsman, Cub Cadet, Husqvarna, Toro, Ariens, Murray, Hustler, Scag, Exmark, Ferris, Snapper, Simplicity, and Dixie Chopper.

Whether you're a homeowner or a professional landscaper, we have the parts you need to keep your equipment running smoothly. Shop our online store today or visit one of our convenient locations to find the perfect replacement parts for your Cub Cadet RZT or any other piece of outdoor power equipment.

Shop Cub Cadet Parts at Madison Tractor!

🔍 Can't Find Your Part?

Use our AI-Powered Part Finder to search by your equipment's make, model, and what you need. It's the fastest way to find the exact part for your machine.

Try the Part Finder →