Kohler Head Gasket: Command & Courage Engines
A blown Kohler head gasket can lead to significant engine problems. This guide will walk you through identifying symptoms, selecting the correct replacement, and installing a new head gasket on your Kohler Command or Courage engine. Keep your lawnmower or outdoor power equipment running smoothly!
Introduction to Kohler head gaskets
The kohler head gasket is a critical component in your Kohler Command or Courage engine. It sits between the cylinder head and the engine block, creating a vital seal that prevents combustion gases, oil, and coolant from leaking. When this seal fails, it can lead to a loss of power, overheating, and even engine damage. If you own a lawnmower, zero-turn mower, or other outdoor power equipment from brands like John Deere, Craftsman, Cub Cadet, Husqvarna, Toro, Ariens, Murray, Hustler, Scag, Exmark, Ferris, Snapper, Simplicity, or Dixie Chopper with a Kohler engine, understanding how to diagnose and replace a faulty head gasket is essential for maintaining peak performance.
Recommended Parts for This Guide
1 part we recommend — in stock, ships fast, one-click add to cart.
🔍 Looking for a specific part? Try our AI Part Finder — tell it your equipment and what you need, and it will find matching parts instantly.
At Madison Tractor Company, we understand the importance of having the right parts for the job. We carry a wide selection of Kohler head gaskets and other essential engine parts. Be sure to also check our article on Briggs & Stratton Head Gasket: By Engine Model for comparison.
Identifying a Failing Kohler Head Gasket
Recognizing the symptoms of a failing Kohler head gasket early can prevent more extensive and costly repairs. Here are some common signs to watch out for:
- Loss of Power: A blown head gasket can cause a significant reduction in engine power, especially under load. You might notice your mower struggling to cut through thick grass.
- Overheating: Leaking combustion gases can disrupt the engine's cooling system, leading to overheating. Keep an eye on the engine temperature and be aware of any warning lights.
- White Smoke: White smoke from the exhaust is a telltale sign that coolant is leaking into the combustion chamber. This is a serious issue that needs immediate attention.
- Bubbling Coolant: If your engine has a coolant reservoir, check for bubbles. Bubbles in the coolant indicate that combustion gases are leaking into the cooling system.
- Milky Oil: Coolant leaking into the oil can create a milky, frothy appearance. This can damage engine bearings and other critical components.
- External Leaks: You might notice oil or coolant leaking from the head gasket area. Look for wet spots or stains around the cylinder head.
- Increased Oil Consumption: A leaking head gasket can cause oil to burn in the cylinder, leading to increased oil consumption.
Tools and Materials Needed for Head Gasket Replacement
Before you begin the replacement process, make sure you have all the necessary tools and materials. This will save you time and frustration.
- New Kohler Head Gasket: Ensure you purchase the correct head gasket for your specific Kohler engine model.
- Socket Set: A set of sockets and wrenches will be needed to remove and install bolts and fasteners.
- Torque Wrench: A torque wrench is essential for tightening the cylinder head bolts to the correct specification.
- Screwdrivers: Both Phillips and flathead screwdrivers will be needed.
- Pliers: Pliers are useful for removing hoses and other small parts.
- Scraper: A scraper will help you clean the old gasket material from the cylinder head and engine block.
- Cleaning Solvent: Use a cleaning solvent to clean the mating surfaces.
- Shop Rags: Keep plenty of shop rags on hand for cleaning up spills and wiping down parts.
- valve cover gasket (Optional): If you're removing the valve cover, consider replacing the valve cover gasket as well.
- Gasket Sealer (Optional): Some technicians use a thin coat of gasket sealer on the head gasket for added protection.
Step-by-Step Kohler Head Gasket Replacement Guide
Safety First: Before starting any repair work, disconnect the spark plug wire to prevent accidental starting. Allow the engine to cool completely. Work in a well-ventilated area.
- Preparation: Remove any shrouds or covers that are blocking access to the cylinder head. Drain the oil and coolant, if applicable.
- Disconnect Components: Disconnect the fuel line, throttle cable, and any other components attached to the cylinder head or valve cover. Refer to our article on Kohler Fuel Pump: Pulse Pump for Command & Courage if fuel lines are brittle or damaged.
- Remove the Valve Cover: Carefully remove the valve cover. Inspect the valve cover gasket and replace it if necessary.
- Remove the Cylinder Head: Loosen the cylinder head bolts in a crisscross pattern to avoid warping the head. Once all the bolts are loose, remove them completely and carefully lift the cylinder head off the engine block.
- Clean the Mating Surfaces: Use a scraper and cleaning solvent to remove all traces of the old head gasket from both the cylinder head and the engine block. Ensure the surfaces are clean and smooth.
- Install the New Head Gasket: Carefully position the new Kohler head gasket onto the engine block. Make sure it aligns correctly with the bolt holes and coolant passages.
- Reinstall the Cylinder Head: Carefully lower the cylinder head onto the engine block, aligning it with the head gasket and bolt holes.
- Tighten the Cylinder Head Bolts: Install the cylinder head bolts and tighten them in a crisscross pattern to the torque specification recommended by Kohler. Use a torque wrench to ensure accurate tightening.
- Reinstall the Valve Cover: Reinstall the valve cover and tighten the bolts to the specified torque.
- Reconnect Components: Reconnect the fuel line, throttle cable, and any other components you disconnected earlier.
- Refill Fluids: Refill the engine with oil and coolant, if applicable.
- Test Run: Reconnect the spark plug wire and start the engine. Check for any leaks or unusual noises.
Choosing the Right Kohler Head Gasket
Selecting the correct Kohler head gasket is crucial for a successful repair. Kohler offers different head gaskets for different engine models, so it's essential to choose the one that's specifically designed for your engine. Using the wrong head gasket can lead to leaks and engine damage. Ensure you know the engine model and specification number to order the correct part. We have many Kohler parts available, including carburetors. Make sure your carburetor is not causing a similar loss of power.
When purchasing a Kohler head gasket, consider the following factors:
- Engine Model: Verify the engine model number to ensure compatibility.
- Material: Kohler head gaskets are typically made from composite materials or metal. Choose a material that is suitable for your engine and operating conditions.
- Quality: Purchase a high-quality head gasket from a reputable supplier like Madison Tractor Company to ensure a proper seal and long-lasting performance.
Preventing Future Head Gasket Failures
While replacing a Kohler head gasket is a necessary repair, there are steps you can take to prevent future failures:
- Regular Maintenance: Follow the manufacturer's recommended maintenance schedule, including regular oil changes and coolant flushes.
- Avoid Overheating: Overheating is a major cause of head gasket failure. Ensure your engine's cooling system is functioning properly.
- Proper Torque: When tightening cylinder head bolts, use a torque wrench and follow the manufacturer's specified torque values.
- Quality Parts: Use high-quality replacement parts, such as belts, blades, spindles, pulleys, filters, spark plugs, bearings, and shear pins, to maintain engine performance and prevent strain on the head gasket.
Shop Kohler Parts at Madison Tractor Company
At Madison Tractor Company, we're committed to providing you with the highest quality Kohler parts and exceptional customer service. Whether you need a kohler head gasket, fuel pump, or any other small engine component, we have you covered. We also carry a wide selection of parts for other popular brands, including Briggs & Stratton, Kawasaki, and more. Browse our extensive online catalog today and find the parts you need to keep your outdoor power equipment running smoothly. Need a carburetor rebuild kit? We carry Small Engine Carburetor Rebuild Kit: Gaskets & Needles as well as Briggs & Stratton Carburetor Rebuild Kit: All Models.
🔍 Can't Find Your Part?
Use our AI-Powered Part Finder to search by your equipment's make, model, and what you need. It's the fastest way to find the exact part for your machine.
Try the Part Finder →Part of our comprehensive guide
Small Engine Parts Guide: Carburetors, Fuel Pumps & Gaskets by Engine








